tubeaudio

All posts tagged tubeaudio

Having recently completed the mods to my Bravo v2 hybrid tube amp, I felt the itch to mod the headphone amp I use at home, my Gemtune APPJ PA1502A. This amp provides full tube amplification instead of a hybrid design. I picked this amp from Massdrop at a very reasonable price. Unlike the Bravo, this promised to be an amp that did not need mods, only a good set of tubes to bring it to life. Stock the sound was crystal clear, but too flat in the lower ends for me, expanding the bass would be a priority. Upgrading to better tubes made a world of difference. Once I had broken in the new set of tubes I decide to perform a small mod and upgrade the inter-stage coupling caps, this sound deepen the bass even further.

Stock APPJ PA1502A

Stock Gemtune APPJ PA1502A with the original tubes

Rolling New Tubes

This is the easiest mod that one can perform, replacing the tubes with better ones. Replace the 6N4 with a 12AX7 or 5751 type tube. I’m currently running a Sovtek 5751. Next the two 6P6Ps should be replaced with a pair of good quality 6V6s or 6L6s. I have a set of Tung-Sol 6V6GTs and a set of JJ Electronics 6L6GCs that I have tried in the amp. Both sound great, but I am a fan of the 6L6s. The 6L6 is both physically larger and a more electronically demanding tube, but one that the circuit specs state it can handle.  They will put out more heat, so if that’s a concern, stick with the 6V6.

The 6L6GC is a much larger tube than the 6P6P

The 6L6GC is a much larger tube than the 6P6P

I have also added tube risers. The stock tube connectors are only secured through solder and I had some fear of damaging them when swapping tubes. I added tube risers that take the brunt of the force when swapping tubes around.

Tube risers

Tube risers

Once the tubes were swapped and broken in I was very happy. Break in time seems to be very important for amps such as this. When I first got the amp I had to run it for at least a few hours before it started to sound right. Once I swapped the tubes and let it warm up for another few hours the sound was richer, bass was deeper, and still crystal clear. I’ve read that these amps and any new tubes need to be burned in for at least 48 hours, so expect slight improvements until burn in is complete.

Replacing the Inter-Stage Coupling Capacitors

This is a very simple mod, one that should increase the deepness of the bass, making the amp a bit more lively. I debated performing this mod as I was already very happy with the amp and the 6L6 mod fixed the flatness from the lower end. The inter-stage coupling circuit for this amp uses two 0.1uF 400V ceramic capacitors, these can be replaced with 0.47uF 400V capacitors.

First we need to remove the four screws holding the top of the amp. This top also contains the transformers, which can easily be detached from the main circuit board through four plugs

Top

Remove the four top screws to expose the top of the board. The plugs for the transformed will unplug easily.

Next we need to remove the four feet and the six outer screws holding the bottom plate on. On my amp there is a seventh screw, but it is screw to a post that is screw into nothing.

Bottom

The four feet and six outer screws need to be removed to access the bottom

Bottom of the APPJ PA1502A

The bottom of the amp, exposing the two ceramic capacitors to swap

Next I de-soldered the two ceramic capacitors. The below images show the solder points that I hit with my de-soldering iron .

IMG_8091 IMG_8094 IMG_8090 IMG_8088

Finally the new capacitors were soldered onto the board and the board reassembled and tested.

Inter-stage capacitor upgrade complete

Inter-stage capacitor upgrade complete. White ceramic 0.1uF 400V caps replaced with orange  0.47uF 400V caps.

Next I powered it up and verified that I didn’t short anything out before reassembling.

IMG_8097 IMG_8096

No fire, no sparks, the audio is clear, and my headphones sound great, time to reassemble and put back where it belongs.

Gemtune APPJ PA1502A in use

Gemtune APPJ PA1502A in use back where it belongs

Afterthoughts

I spoil myself with this amp, the clarity of the audio is almost startling. I have the amp paired up with a pair of Beyerdynamic DT990 600 ohm headphones. Not a combination that is bass heavy without the mods, but one that will provide some serious HD audio. I let my boyfriend listen to the amp while it was burning it, his eyes told me all I needed to know. Afterwards he described the experience as disturbingly HD, kinda like the first time watching a HD or 48fps movie, almost too lifelike. Goal achieved ^__^

In March I picked up one of these little Bravo Audio V2 class A hybrid tube amps on sale. This neat little headphone amp uses a 12AU7 vacuum tube to provide that ‘warmth’. There are plenty of articles, reviews, and forum posts that go into the details of what this little amp is capable of, plus it’s moddable. I bought it because I love tube audio and I could have some fun and tweak it.

 Bravo v2 Original

First Impressions

This amp looks like it was designed to be modded, but the reality is that the PCB is rather fragile. Traces are prone to falling off, especially if you use a soldering iron that is too hot. The first thing I had to do to mine was retin it with fresh high quality solder. It looked like it had been soldered with J-B Weld, plus it cleared up the audio. Once that was done I started swapping different 12AU7 tubes from my collection, eventually decided on an Electro-Harmonix for daily use. The stock tube didn’t sound bad, but the new EH 12AU7A seemed to handle the highs and lows better. I tested a vintage clear-top RCA, but the low ends sounded muddled, it is possible that the tube is failing. I proceeded to use the amp in this configuration at my job.

 Bravo v2 Original

Time To Perform the Mods – Easy First

The most common mods are component upgrades. Replace the electrolytic capacitors with higher quality 35V caps. Interestingly enough, when I was replacing the caps, I saw that the circuit board states that these should be 35V. This is an easy mod, there are only three caps, 1 – 6800uF, 2 – 1000uF.

New power cap

Final result with new power cap

Upgrade the MOSFETs – Hard Next

Replacing the IRF630Ns with almost any of the IRF510-530 series will improve the soundstage and roll-off. I opted to replace mine with the IRF530N, an improved version of the IRF510. This mod is not as easy as the heat sinks for the MOSFETs should be replaced with larger ones to handle the increased power consumption and thus heat generation. On my board I had to drill out the old heatsink mounts, and some of these mounts do go near traces. I do not have precision tools.

Work in progress on the amp

Work in progress on the amp

In progress fitting of the heatsinks

In progress fitting of the heatsinks

New IRL530N MOSFETs

New IRL530N MOSFETs

The Final Results

I have been using the amp daily for the past week. It sounds so much better now, a noticeable improvement. I consider the amp and the mods a worthwhile improvement.

The final result

The final result